Tekla/steel detailing Question paper-10

                       

1).What are the three grade identification colors for ASTM F1554 anchor rods?

F1554-GR.36_BLUE IN COLOUR.

F1554-GR.55_YELLOW IN COLOUR.

F1554-GR.55_RED IN COLOUR.

2).When columns do not have enough local strength, what type of reinforcing

is required to reinforce for web panel-zone shear at a moment connection?

EITHER DOUBLER PLATES OR DIAGONAL STIFFENERS

3.What material type is commonly used for rolled floor plate?

ASTM A786  IS THE MOST COMMONLY USED ROLLED

FLOOR PLATE.

4.Why are fillet welds preferred over groove welds?

Fillet welds generally require less weld metal than groove welds. Additionally, fillet welds do

not generally require beveling and similar base metal preparation. As a result, fillet welds are

generally more economical to make than groove welds. Thus, fillet welds are preferred.

5.Draw Flare Bevel Weld Symbol & Its Condition?

FLARE WELD IS MOST COMMONLY USED TO JOIN  A ROUND OR CURVED PIECE TO

    A FLAT PIECE.

6.Full form of SEOR and GOL?

SEOR_STRUCTURAL ENGINEER OF RECORD.

GOL_GAUGE ON LEG.

7.What is the material grade for twist of type bolts?

 

ASTM F1852 .

8.Please write down the types of beam?

1.sloped beam

2.skwed beam

3.curved beam

4.canted beam

5.hip and valley beam.

9.what is the distance between  hoop to hoop distance in ladder?

4'-0.

10.what is masonry?

The part of building that are made of stone or brick.

Tekla TEST question paper-9_

1.     High-strength bolts used for the vast majority of field connections are furnished in what two grades?

 A325

A490 

2. The spacing between bolts in standard bolted connections is usually?

3"

3. Currently, the two primary methods of fastening together the major components of a steel-frame structure are BOLTING________and ____WELDING______

4.What angle length is required for a 5-row bolted connection?

1'-3"

5.    Give standard Slot size of 1” dia bolt?

1 1/6"X1"5/16

6.Distance between floor to floor landings is called?

FLIGHT

7    .Maximum column length without splice………. Ft.?

40'-0"

8.What is abbreviation for RFI?

Request for information.

9.  What depth scale is usually used for most steel columns?

12

10.FULL FORM OF BOD,FOW AND JBE?

BOD:BOTTOM OF DECK

FOW:FACE OF WALL

JBE:JOIST BEARING ELEVATION.

1111.When drawing a fillet weld symbol, the size of the fillet weld is always Called out on which side of the symbol?                                                                                                      LEFT SIDE OF THE SYMBOL.

1112 As a detailer what care you need to take if you have SC bolts in a connection?               OVERSIZED HOLES  TO BE PROVIDED                                                                             NO PAINT 3" AROUND HOLES

O

L

4 

Tekla interview Question-8

 1.FULL FORM OF ABM ,B.O.BP AND T.O.G?

ABM:ADVANCE BILL OF MATERIALS.

BOBP:BOTTOM OF BASE PLATE.

T.O.G:TOP OF GRATING.

2.WHY  SLOTTED HOLES PROVIDED  IN STEEL MEMBER?

FOR FIELD ADJUSTMENT WE NEED TO PROVIDED SLOTS IN STEEL MEMBER.

ALSO PLEASE NOTE ,LONG SLOTTED HOLES TO BE PROVIDED AT EXISTING CONDITIONS FOR ERECTION FEASABILITY.

3.PLEASE DRAW BEAM RUNNING OVER COLUMN WITH STIFFENERS IN BEAM WEB?

STIFFENERS IS USED TO WITHSTANDS LOADS AND ALSO USED TO TRANSFER LOADS

4.WHAT IS THE TOLERANCES FOR OVERSIZED HOLE AND STANDARD HOLE?

FOR OVERSIZED HOLE-3/16

FOR STANDARD HOLE-1/16

5.WHAT ARE THE MAIN REPORTS NEED TO SEND FOR FABRICATION WHILE SENDING DRAWINGS?

1.DXF

2.NC FILES

3.KISS LIST

4.FABTROL REPORTS

5.BOLT REPORTS

6.DWG FILES

7.TRANSMITTAL.

6.WHAT IS GALVANIZATION AND WHAT IS THE SURFACE PREPARATION FOR GALVANIZED MEMBER?

GALVANIZATION:PROCESS OF ADDING ZINC COATING TO THE METAL TO AVOID CORROSSION.

ASTMA123 IS THE SURFACE PREPARATION FOR GALVANIZED MEMBER

7.WHAT IS THE STOCK LENGTH FOR PLATES ,ANGLES AND BENT PLATES?

ANGLE-20'-0

BENT PLATE-10'-0

PLATE-10'-0.

8.WHAT IS ENCROACHMENT?

THE PERMISSIBLE DISTANCE BEYOND THE WORKABLE GAGE OR THE LIMITED DISTANCE TO ENTER IN TO FILLET OR ROUNDING RADIUS.

GENERALLY TERMED AS "K" VALUE.

?

9.HOW TO FIX WORKPOINTS IN BRACING ?

WORKPOINT PASSES THROUGH THE GAUGE LINE IN CASE OF BOLTING.

WORKPOINT PASSES THROUGH CENTRE OF GRAVITY IN CASE OF WELDING

10.DERVIE E70XX?

E-ELECTRODE

7-TENSILE STRENGTH

X-WELD POSITION

X-ELECTIC CURRENT USED

11.IF HSS COLUMN AND HSS BEAM ARE DIRECTLY WELDING IN FIELD THEN WHAT IS THE MAIN THING REQUIRE FOR FIELD WELDING?

ERECTION AID-(Angle)

12.WHAT IS THE WIDTH OF LADDER AND MAXIMUM LENGTH  OF A LADDER?

WIDTH-1'-6"

LENGTH-20'-0

13.WHEN SEISMIC LOADS WILL FORM?

THE LOADS WHICH ARE FORMED BY SUDDEN VIBRATIONS IS KNOWNS AS SEISMIC LOADS.

GENERALLY SEISMIC LOADS ALSO KNOWN AS EARTHQUAKE LOADS.

14.WHAT IS A POST?

IF WEIGHT IS LESS THAN 300LBS AS PER OSHA THEN WE CALL IT AS POST.

IF WEIGHT IS MORE THAN 300LBS THEN IT WILL BE COLUMN.

15.WHAT ARE THE MAIN FACTORS TO DESIGN A CONNECTION BETWEEN BEAM TO BEAM?

NORMALLY CONNECION DESIGNER WILL DESIGN THE CONNECTION BASED ON LOADS(KIPS)

BASED ON STRUCTURAL ENGINEER REQUIREMENTS.

TEKLA & STEEL DETAILING QUESTIONS INTERVIEW-7

 1.FULL FORM OF NISD AND HVAC?

NISD:NATIONAL INSITITUTE OF STEEL DETAILING.

HVAC:HEAT VENTILATION AND AIR CONDITIONING

2.WHAT IS THE SHORTCUT  TO OPEN DRAWING LIST IN TEKLA?

MODELER EDITOR:CTRL+L

DRAWING EDITOR: CTRL+O

3.MENTION SOME CONDITIONS WHERE ALL AROUND FILET WELD APPLICABLEDE?

1.BASE PLATE & COLUMN

2. BEAM &END PLATE 

3. CAP PLATE & COLUMN

4.IF DESIGN DRAWING DOES NOT FURNISH WELD SIZE THEN  HOW TO DETERMINE WELD SIZE BETWEEN TWO MEMBERS ?

WELD SIZE  TO BE CONSIDER BASED ON  THE LOWEST THICKNESS BETWEEN TWO MEMBERS 

5.DERIVE BU4-GF?

B-BUTT WELD

U-UNLIMITED BASE METAL THICKNESS

4-SINGLE BEVEL

GF-WELDING PROCESS

6.HOW TO FIX RUNGS IN LADDER ?

FIRST WE NEED TO FIX TOP OF RUNG EQUAL TO  TOP OF FINISIED LEVEL OR TOP OF GRATING  THEN WE NEED TO SPACE THE RUNGS.

GENERALLY RUNG TO RUNG SPACING SHOULD BE 1-0

7.WHAT IS THE OVERHEAD CLEARENCE BETWEEN STAIR AND FLOOR AS PER OSHA?

6'-8" TO BE MAINTAINED

8.WHAT IS THE RULE BETWEEN STRINGER WIDTH AND LANDING CLEARENCE ?

LANDING  CLEARENCE SHOULD BE MORE THAN THE STRINGER WIDTH.THIS A GENERAL PRACTICE TO DETAIL STAIR LANDING

9.WHAT IS THE MAX TREAD AND RISER DIMENSION  IN  STAIR?

RISER SHOULD BE  MAX 7"

TREAD SHOULD BE  MAX 11"

10.WHAT IS THE MAXIMUM SPACING TO BE MAINTAINED  BETWEEN POST TO POST AND PICKET TO PICKET?

POST TO POST-4'-0

PICKET TO PICKET-4"

11.HANDRAIL HEIGHT TO BE FIXED FROM?

NOSING LINE OR TOP OF FINISHED FLOOR.

12.DEFINE NOSING LINE?

THE LINE WHICH TOUCHES ALL NOSING POINTS IS KNOWN AS NOSING LINE

NOSING POINT: INTERSECTION OF PAN TREAD AND RISER 

13.HOW TO CONNECT WALL RAIL TO WALL?

CONNECTION BETWEEN WALL AND WALL RAIL  BY USING WALL BRACKET .

GENERALLY WALL BRACKET IS A BOUGHT ITEM.

14.WHAT IS THE ANGLE  TO DETAIL STAIR AS PER OSHA?

STAIR ANGLE SHOULD BE  30 DEGREE TO 50 DEGREE TO DETAIL STAIR.